Standard
By Aryo Wisnudarto
Software
By Aryo Wisnudarto
Compress - http://www.codeware.com/
software for the design and analysis of ASME Section VIII pressure vessels and heat exchangers.
PV Elite - http://www.codecad.com/
PV-Elite is a graphical based, easy-to-use software program that provides engineers, designers, estimators, fabricators and inspectors with complete design capabilities of tall towers, horizontal vessels, individual vessel and heat exchangers. PV-Elite has a component analysis module, CodeCalc, which is also available as a separate program.
CodeCalc - http://www.codecad.com/
CodeCalc analyzes all of the individual components of a typical pressure vessel or heat exchanger, including shells, heads, legs, lugs, nozzles (with strength path calculations), cones, floating heads, tubesheets (both TEMA and ASME) and flanges.
Zick analysis, WRC 107, and calculations for legs and lugs are also included. Dimensional input data can be quickly checked by reviewing a simultaneous dimensioned sketch of the component.
Output lists the equations used to solve for the important results and has extensive reference to the standard used for the calculation. Having been around since 1987, CodeCalc maintains its popularity today because of its range of applications, user-friendliness, economy, reliability and our unparalleled technical support.
DIMy - http://www.tuev-nord.de
Pressure Vessel design and analysis to the German DIN AD-Merkblätter code is available as a combined set of subroutines as follows. SI units are used, and full printout of intermediate results and calculated factors is produced. This is a DOS-based program, but has an easy to use Windows-like interface.
Rotating Equipment
By Aryo Wisnudarto
Pump
A machine that draws a fluid into itself through an entrance port and forces the fluid out through an exhaust port (see illustration). A pump may serve to move liquid, as in a cross-country pipeline; to lift liquid, as from a well or to the top of a tall building; or to put fluid under pressure, as in a hydraulic brake. These applications depend predominantly upon the discharge characteristic of the pump. A pump may also serve to empty a container, as in a vacuum pump or a sump pump, in which case the application depends primarily on its intake characteristic. Type of pump: Centrifugal pump; Compressor; Displacement pump; Fan; Fuel pump; Pumping machinery; Vacuum pump.
Compressor
A machine that increases the pressure of a gas or vapor (typically air), or mixture of gases and vapors. The pressure of the fluid is increased by reducing the fluid specific volume during passage of the fluid through the compressor. When compared with centrifugal or axial-flow fans on the basis of discharge pressure, compressors are generally classed as high-pressure and fans as low-pressure machines.
Compressors are used to increase the pressure of a wide variety of gases and vapors for a multitude of purposes. A common application is the air compressor used to supply high-pressure air for conveying, paint spraying, tire inflating, cleaning, pneumatic tools, and rock drills. The refrigeration compressor is used to compress the gas formed in the evaporator. Other applications of compressors include chemical processing, gas transmission, gas turbines, and construction. See also Gas turbine; Refrigeration.
Compressor displacement is the volume displaced by the compressing element per unit of time and is usually expressed in cubic feet per minute (cfm). Where the fluid being compressed flows in series through more than one separate compressing element (as a cylinder), the displacement of the compressor equals that of the first element. Compressor capacity is the actual quantity of fluid compressed and delivered, expressed in cubic feet per minute at the conditions of total temperature, total pressure, and composition prevailing at the compressor inlet. The capacity is always expressed in terms of air or gas at intake (ambient) conditions rather than in terms of arbitrarily selected standard conditions.
Air compressors often have their displacement and capacity expressed in terms of free air. Free air is air at atmospheric conditions at any specific location. Since the altitude, barometer, and temperature may vary from one location to another, this term does not mean air under uniform or standard conditions. Standard air is at 68°F (20°C), 14.7 lb/in.2 (101.3 kilopascals absolute pressure), and a relative humidity of 36%. Gas industries usually consider 60°F (15.6°C) air as standard.
Compressors can be classified as reciprocating, rotary, jet, centrifugal, or axial-flow, depending on the mechanical means used to produce compression of the fluid, or as positive-displacement or dynamic-type, depending on how the mechanical elements act on the fluid to be compressed. Positive-displacement compressors confine successive volumes of fluid within a closed space in which the pressure of the fluid is increased as the volume of the closed space is decreased. Dynamic-type compressors use rotating vanes or impellers to impart velocity and pressure to the fluid.
Turbine
Turbines are devices that spin in the presence of a moving fluid. The difference between water wheels or windmills and turbines is largely one of emphasis and degree. During the 18th and 19th centuries, much progress was made toward extracting the kinetic energy of flowing water by devising water turbines. Leonhard Euler, applying fluid mechanics, developed a water turbine as early as 1750. During the 18th century several engineers, such as Benôit Fourneyron, succeeded in building water turbines that by far outstripped conventional water wheels by giving the blades special shapes. The term "turbine" was coined by Fourneyron's professor Claude Burdin; he derived the term from turbo, a spinning object.
The most useful turbines for many purposes are those that can be propelled with energy from heat. A typical turbine based on heat is the steam turbine. The idea of a steam turbine is much older than the steam engine itself. Around 60 bce the Alexandrian Greek Heron (a.k.a. Hero) used jets of steam to turn a kettle. In 1629 the Italian engineer Giovanni Branca depicted in his machine book Le Machine a steam turbine in which a jet of steam is directed at the vanes of the same sort of apparatus as a water wheel. No doubt others observed that escaping steam is like the rushing wind and could be used to push mills just as the wind powers windmills.
When practical steam engines were built at the start of the 18th century, however, they moved a cylinder back and forth (reciprocating motion) instead of pushing a wheel around, although they could be made to turn wheels with various ingenious mechanisms. Reciprocating steam engines were bulky, had slow rotation speeds, and wasted much energy in the machine itself to move the heavy pistons back and forth. When first used to drive electric generators, reciprocating steam engines proved difficult to maintain at a fixed rotation speed as the load on the generator changed.
Turbines are as simple as reciprocating engines are complex. Because they have essentially only one moving part, they are sometimes called the perfect engines, almost directly turning heat into rotary motion.
The first to build a steam turbine was the British engineer Charles Algernon Parsons. In 1884 he completed a small turbine that rotated at 18,000 revolutions per minute and that delivered 10 horsepower. The Swedish engineer Carl Gustav de Laval, experimenting with steam turbines, achieved greater power and higher rotation rates. In 1890 he built a turbine consisting of a 30-cm (12-in.) disk with 200 blades mounted on a flexible axis. The steam was admitted to the blades by special nozzles (
The design of steam turbines developed into a science near the end of the 19th century. Better materials allowed the construction of turbine blades that are resistant to corrosion. Charles Curtis developed the multistage turbine in which the blades and disks become progressively larger when the steam expands. Parsons developed in 1894 the ship turbine engine. The slow-revolving turbine consisted of several sections of increasing diameter. High-pressure steam is admitted to the turbine and pressure differences in each section drive the turbine blades. The first ship to be equipped with such a steam turbine, the Turbinia, immediately established a speed record with 31 knots (57.5 km or 35.7 mi per hour). During the early years of the 20th century, most reciprocating steam engines were replaced by steam turbines (or by diesels). Steam turbines can deliver much more power than reciprocating engines and need less maintenance. Steam turbines also supplanted marine steam engines on ships.
A similar evolution took place for large internal combustion engines, mainly driven by the need for lightweight and powerful airplane engines. Most large modern airplanes are now powered by either turboprop or turbojet engines. These turbines are spun by the expansion of jet fuel instead of by the expansion of water into steam.
Generator
A machine in which mechanical energy is converted to electrical energy. Generators are made in a wide range of sizes, from very small machines with a few watts of power output to very large central-station generators providing 1000 MW or more. All electrical generators utilize a magnetic field to produce an output voltage which drives the current to the load. The electric current and magnetic field also interact to produce a mechanical torque opposing the motion supplied by the prime mover. The mechanical power input is equal to the electric power output plus the electrical and mechanical losses.
Generators can be divided into two groups, alternating current (ac) and direct current (dc). Each group can be subdivided into machines that use permanent magnets to produce the magnetic field (PM machines) and those using field windings. A further subdivision relates to the type of prime mover and the generator speed. Large generators are often driven by steam or hydraulic turbines, by diesel engines, and sometimes by electric motors. Generator speeds vary from several thousand rotations per minute for steam turbines to very low speeds for hydraulic or wind turbines. See also Diesel engine; Hydraulic turbine; Motor; Prime mover; Steam turbine; Wind power.
The field structure of a generator establishes the magnetic flux needed for energy conversion. In small generators, permanent magnets can be used to provide the required magnetic field. In large machines, dc field windings are more economical and permit changes in the magnetic flux and output voltage. This allows control of the generated voltage, which is important in many applications. In dc generators the field structure must be stationary to permit a rotating mounting for the commutator and armature windings. However, since the field windings require low voltage and power and have only two lead wires, it is convenient to place the field on the rotating member in ac generators. See also Electric power generation; Electric rotating machinery; Windings in electric machinery.
Static Equipment
By Aryo Wisnudarto
Pressure Vessel
Pressure vessels are used in a variety of applications. These include the industry and the private sector. They appear in these sectors respectively as industrial compressed air receivers and domestic hot water storage tanks, other examples of pressure vessels are: diving cylinder, recompression chamber, distillation towers, autoclaves and many other vessels in mining or oil refineries and petrochemical plants, nuclear reactor vessel, habitat of a space ship, habitat of a submarine, pneumatic reservoir, hydraulic reservoir under pressure, rail vehicle airbrake reservoir, road vehicle airbrake reservoir and storage vessels for liquified gases such as ammonia, chlorine, propane, butane and LPG.
In the industrial sector, pressure vessels are designed to operate safely at a specific pressure and temperature, technically referred to as the "Design Pressure" and "Design Temperature". A vessel that is inadequately designed to handle a high pressure constitutes a very significant safety hazard. Because of that, the design and certification of pressure vessels is governed by design codes such as the ASME Boiler and Pressure Vessel Code in North America, the Pressure Equipment Directive of the EU (PED), Japanese Industrial Standard (JIS), CSA B51 in Canada, AS1210 in Australia and other international standards like Lloyd's, Germanischer Lloyd, Det Norske Veritas, Stoomwezen etc.
Atmospheric Tank
Definition of an atmospheric tank means a storage tank which has been designed (emphasis added) to operate at pressures from atmospheric through 0.5 psig (pounds per square inch gauge, 3.45 kpa.) An atmospheric tank containing a flammable liquid that has a feeder connection to the fill process you described would not be covered by the PSM standard. The rationale for this interpretation is that the process described above only included the activities of storage and associate transfer to storage in containers which for the purpose of the PSM standard are considered equivalent to atmospheric tanks which are excepted from PSM coverage as noted previously.
Heat Exchanger
A device used to transfer heat from a fluid flowing on one side of a barrier to another fluid (or fluids) flowing on the other side of the barrier.
When used to accomplish simultaneous heat transfer and mass transfer, heat exchangers become special equipment types, often known by other names. When fired directly by a combustion process, they become furnaces, boilers, heaters, tube-still heaters, and engines. If there is a change in phase in one of the flowing fluids—condensation of steam to water, for example—the equipment may be called a chiller, evaporator, sublimator, distillation-column reboiler, still, condenser, or cooler-condenser.
Heat exchangers may be so designed that chemical reactions or energy-generation processes can be carried out within them. The exchanger then becomes an integral part of the reaction system and may be known, for example, as a nuclear reactor, catalytic reactor, or polymerizer.
Heat exchangers are normally used only for the transfer and useful elimination or recovery of heat without an accompanying phase change. The fluids on either side of the barrier are usually liquids, but they may also be gases such as steam, air, or hydrocarbon vapors; or they may be liquid metals such as sodium or mercury. Fused salts are also used as heat-exchanger fluids in some applications.
Most often the barrier between the fluids is a metal wall such as that of a tube or pipe. However, it can be fabricated from flat metal plate or from graphite, plastic, or other corrosion-resistant materials of construction.
Heat exchangers find wide application in the chemical process industries, including petroleum refining and petrochemical processing; in the food industry, for example, for pasteurization of milk and canning of processed foods; in the generation of steam for production of power and electricity; in nuclear reaction systems; in aircraft and space vehicles; and in the field of cryogenics for the low-temperature separation of gases. Heat exchangers are the workhorses of the entire field of heating, ventilating, air-conditioning, and refrigeration. See also Conduction (heat); Convection (heat); Cooling tower; Distillation; Evaporator; Heat radiation; Heat transfer; Vapor condenser.
About
By Aryo Wisnudarto
Regret will be the first word when I started this blog. I should do this from few years back.
I never written anything all my life, except for my work report he..he..he…
Now I want to learn how to write and I have to force right side of my brain to get more excercise.
My name is Aryo Wisnudarto, I was born in Jakarta, 16 February 1981, and my education background is Mechanical Engineer. Now I am working on the Oil & Gas sector. What I want to write in my blog is everything that has related with my education, my job and my knowledge in oil & gas sector. I do hope this blog can be useful to other people and I will be very grateful if there are someone wants to contribute in my blog.
